N-0008
STEP 1:
Let’s start at the center going to the right end of the necklace. Cut a 6in. beadalon wire (BC07-021BT-30).
STEP 2:
On one end, string a crimp bead (FMCRBD2S-15) and a metal “o” ring (MPS4018-H). Go back through the crimp bead. Crimp the crimp bead.
STEP 3:
On the other end, thread an agoha seed (CNA10X12G), a coco tusk (COS1500Y), a buri bead (PLM2108GR), a flat disc (LSMS023), a coco tusk, a buri bead, a flat disc, a coco tusk, a buri bead, a flat disc, a coco tusk, a flat disc, a buri bead, a crimp bead (FMCRBD2S-15), an jump ring (SSRJ6-100) and back through the crimp bead and back through the bead just strung. Tighten the wire, close the crimp bead and trim excess wire.
Set aside.
STEP 4:
Cut a 2in. silver wire (SFBW22S) and a 6in. suede lace (BCSF28DB-25).
STEP 5:
Insert one end onto the jump ring. Fold the suede lace about an inch and wrap it with a 2in. silver wire.
STEP 6:
Attach the other end onto a suede end cap (FMSES-144).
STEP 7:
Use a split rings (FMRS8S-144) to attach the suede end cap and a lobster clasp (FMCLLXSMS-144). Right side is now done.
STEP 8:
Repeat steps one and two to make the left neckline.
STEP 9:
On the other end, string a buri bead, a coco heishi (COS1403Y), a flat disc, a jump ring, a mactan shell (SH038G), a flat disc, a coco heishi, a buri bead, a coco heishi, a flat disc, a coco heishi, a buri bead, a crimp bead and a jump ring. Go back through the crimp bead and back through the last bead just strung. Tighten the wire, close the crimp bead and trim excess wire off.
STEP 10:
Repeat steps four up to seven, substituting the lobster clasp with four pieces split rings (FMRS8S-144).
STEP 11:
Cut a 2in. silver wire. Make a simple loop on one end. String a buri bead, make the first half of the wrapped loop and attach to the last split ring. Finish the wraps. Cut off excess wire off.
STEP 12:
Repeat step eleven, substituting the buri bead with an agoha seed. Attach this bead unit onto the jump ring strung near the mactan shell. Left neckline is now done.
STEP 13:
Let’s make the dangle. Cut another 2in. silver wire. On one end make a wrapped loop, slide a turbo shell (SH3120GT). Insert the other end onto the metal “o” ring’s hole. Finish with wrapped loop.
STEP 14:
To finish this project off, on end of another 2in. silver wire make the first half of the wrapped loop, slide a butterfly wood pendant (WDC3636-YG). Finish the wraps. Insert the other end of the wire through the wrapped loop created with turbo shell. Finish with wrapped loop. Trim off excess wire off.
List of Materials:
1 pc. WDC3636-YG yellow green lam. butterfly paper print wrapped wood pendant
1 pc. SH3120GT green turbo coin shell beads
2 pcs. CNA10X12G green agoha seed beads
4 pcs. COS1403Y yellow coco heishi beads
4 pcs. COS1500Y yellow coco tusk beads
8 pcs. PLM2108GR lime green cone buri beads
1 pc. SH038G green mactan pearl shell beads
8 pcs. LSMS023 flat disc silver plated beads
1 pc. FMCLLXSMS-144 silver plated lobster clasp 1 pc. MPS4018-H metalcast silver hammered o’ring pendant
2 pcs. 6in. BC07-021BT-30 beadalon wire 7 bright-021″ diameter
4 pcs. FMCRBD2S-15 silver crimp beads
2 pcs. FMSES-144 silver plated suede end caps
4 pcs. FMRS8S-144 silver plated split rings
5 pcs. SSRJ6-100 open ring
2 pcs. 6in. BCSF28DB-25 dark brown faux suede lace
6 pcs. 2in. SFBW22S silver filled wire dead soft